Lift-All
 Hydra-Tech, Inc., in Fort Wayne, Indiana, one of the leading manufacturers of aerial devices and digger derricks in the United States, was founded in 1981. The original facility was a rented building of 7,000 square feet in which one LIFT-ALL model aerial device was produced. From this humble facility, LIFT-ALL moved to a corporate-owned manufacturing plant of over 100,000 square feet, located on 15 acres of land. More than 120 different models of LIFT-ALL aerial devices and digger derricks are manufactured today.
The rapid growth and success of Hydra-Tech, Inc. is due to the commitment of its employees to superior quality, customer service and product innovation. Future growth and success of Hydra-Tech, Inc. will be powered by four forces; customer service, a strong sense of direction, financial strength and the commitment and enthusiasm of their employees.
LD-45 or LD-47 with the Following Configurations:
- Behind Cab Mount with a Boom Tip Winch
- Behind Cab Mount with a Turntable Winch
- Corner Mount with a Boom Tip Winch
- Corner Mount with a Turntable Winch
- Rear Mount with a Boom Tip Winch
- Rear Mount with a Turntable Winch
|
The above digger derrick configurations are all standard without a bucket, and are available with either one single man side hung bucket (1S) or two single man side hung buckets (2S). |
Lift-All Digger Derricks are available in to sizes, the LD-45 and the LD-47, both offer full pressure hydraulic controls and are designed to provide the same low operating cost that the industry has come to expect from Lift-All.
Standard Equipment:
- Full Pressure Hydraulic Controls
- Steel Hydraulic Second Stage
- Fiberglass Hydraulic Third Stage
- 100 degree Boom Travel (+80/-20)
- 50 Gallon Hydraulic Tank
- New Automatic Transfer Pole Guide
| |
LD-45 |
LD-47 |
| Chassis Specifications |
Consult your dealer for vehicle recommendations. |
| Sheave Height |
45' (13.7m) |
47' (14.3m) |
| Boom Extension |
|
|
| - Inner Boom |
8'-10.1" (2.7m) |
9' - 6.1" (2.9m) |
| - Middle Boom |
8'-9.1" (2.6m) |
9'-5.1" (2.8m) |
| Outer Boom Travel Arc |
|
|
| - Above Horizontal |
80° |
80° |
| - Below Horizontal |
20° |
20° |
| Turntable Rotation |
360° Continuous |
| Hydraulic System (Open-Center) |
|
|
| - Hydraulic Oil Tank Capacity |
50 Gallons (189 L) |
| - Winch and Digger Pressure |
2400 PSI (169 KG/CM2) |
| - Boom Pressure |
2000 PSI (140 KG/CM2) |
| Hydraulic Pump Output (Tandem) |
|
|
| - Winch and Digger Functions |
30 GPM (114LPM) |
| - Boom Functions |
10 GPM (37.9 LPM) |
| - Combined Output |
35 GPM (134 LPM) |
| Maximum Capacity |
|
|
| - Tip Winch |
25,650 lbs (11,635 kg) |
24,600 lbs (11,158 kg) |
| - Turntable Winch |
25,700 lbs (11,657 kg) |
24,700 lbs (11,203 kg) |
| Capcity at 10' Radius |
|
|
| - Tip Winch |
10,850 lbs (4,922 kg) |
10,400 lbs (4,717 kg) |
| - Turntable Winch |
11,000 lbs (4,990 kg) |
10,500 lbs (4,763 kg) |
| |
Sheave Height |
| Model |
D |
E |
F |
| LD-45 |
|
|
|
| Tip Winch |
45' (13.7m) |
36.2' (11m) |
27.6' (8.4m) |
| Turntable Winch |
45' (13.7m) |
36.2' (11m) |
27.6' (8.4m) |
| |
|
|
|
| LD-47 |
|
|
|
| Tip Winch |
47' (14.3m) |
37.5' (11.4m) |
28.3' (8.6m) |
| Turntable Winch |
47' (14.3m) |
37.5' (11.4m) |
28.3' (8.6m) |
| |
|
|
|
| |
Horizontal Reach |
| |
G |
H |
I |
| LD-45 |
|
|
|
| Tip Winch |
18.5' (5.6m) |
27.2' (8.3m) |
36' (11m) |
| Turntable Winch |
18.5' (5.6m) |
27.2' (8.3m) |
36' (11m) |
| |
|
|
|
| LD-47 |
|
|
|
| Tip Winch |
19.2' (5.9m) |
28.7' (8.7m) |
38.1' (11.6m) |
| Turntable Winch |
19.2' (5.9m) |
28.7' (8.7m) |
38.1' (11.6m) |
| |
|
|
|
| |
Load Radius |
| |
A |
B |
C |
| LD-45 |
|
|
|
| Tip Winch |
6.2' (1.9M) |
4.7' (14m) |
3.2' (0.9m) |
| Turntable Winch |
6.2' (1.9M) |
4.7' (14m) |
3.2' (0.9m) |
| |
|
|
|
| LD-47 |
|
| Tip Winch |
6.6' (2m) |
4.9' (1.5m) |
3.3' (1m) |
| Turntable Winch |
6.6' (2m) |
4.9' (1.5m) |
3.3' (1m) |
| |
|
|
|
| |
Digging Radius |
|
| |
J |
K |
|
| LD-45 |
|
|
|
| Tip Winch |
15.9' (4.8m) |
24.7' (7.5m) |
|
| Turntable Winch |
15.9' (4.8m) |
24.7' (7.5m) |
|
| |
|
|
|
| LD-47 |
|
|
|
| Tip Winch |
16.7' (5.1m) |
26.1' (8m) |
|
| Turntable Winch |
16.7' (5.1m) |
26.1' (8m) |
|
| |
|
|
|
|
|
